Other engineering and technology Archives

Question Cagtegory: Other engineering and technology

All Questions

Filter by

Questions Per Page:

Investigate the principles of aerodynamics in mechanical engineering, covering topics such as fluid flow around objects, lift and drag forces, and boundary layer phenomena.
Investigate the principles of aerodynamics in mechanical engineering, covering topics such as fluid flow around objects, lift and drag forces, …
Aircraft performance

incompressible flow

lift and drag

mech.

Worldtech Asked on 1st December 2024 in Mechanical engineering.
- 96 views
- 1 answers
- 0 votes
Two large diffuse gray parallel plates, separated by a small distance, have surface temperature of 400 K and 300 K. If the emmissivities of the surface are 0.8 and the Stefan-Boltzmann constant is 5.67 x 10^-8 W/m3K4, What is the net radiation heat exchange rate in KW/m3 between the two plates?
Two large diffuse gray parallel plates, separated by a small distance, have surface temperature of 400 K and 300 K. …
fluids

heat and mass transfer

Mech_59 Asked on 16th October 2023 in Mechanical engineering.
- 469 views
- 1 answers
- 0 votes
Two concentric spheres of diameters D1 = 0.5 m and D2 = 1 m are separated by an air space as shown in given figure and have surface temperatures of 400 K and 300 K respectively.
Two concentric spheres of diameters D1 = 0.5 m and D2 = 1 m are separated by an air space …
fluids

heat and mass transfer

Mech_59 Asked on 13th October 2023 in Mechanical engineering.
- 473 views
- 1 answers
- 0 votes
Consider a hot, boiled egg in a spacecraft that is filled with air at atmospheric presssure and temperature at all times.
Consider a hot, boiled egg in a spacecraft that is filled with air at atmospheric presssure and temperature at all …
fluids

heat and mass transfer

Mech_59 Asked on 13th October 2023 in Mechanical engineering.
- 472 views
- 1 answers
- 0 votes
Air at 27°C and 1 atm flows over a flat plate at velocity of 2 m/s. Assume that the plate is heated over its entire lenght to a temperature of 60°C.
Air at 27°C and 1 atm flows over a flat plate at velocity of 2 m/s. Assume that the plate …
fluids

heat and mass transfer

Mech_59 Asked on 12th October 2023 in Mechanical engineering.
- 455 views
- 1 answers
- 0 votes
A fluid flowing over a flat plate has the following properties : dynamic viscosity = 25 x 10^-6 kg/ms, specific heat = 2.0 kJ/kgK, thermal conductivity 0.05 W/mK.
A fluid flowing over a flat plate has the following properties : dynamic viscosity = 25 x 10^-6 kg/ms, specific …
fluids

heat and mass transfer

Mech_59 Asked on 12th October 2023 in Mechanical engineering.
- 454 views
- 1 answers
- 0 votes
An aluminium sphere weighning 5.5 kg and initially at a temperature of 290°C is suddenly immersed in a fluid at 15°C. The convective heat transfer coefficient is 58 W/m²K.
An aluminium sphere weighning 5.5 kg and initially at a temperature of 290°C is suddenly immersed in a fluid at …
fluids

heat and mass transfer

Mech_59 Asked on 29th September 2023 in Mechanical engineering.
- 850 views
- 1 answers
- 0 votes
A metallic rod (k = 32 W/m°C), 10 mm in diameter and 80 mm long, with an insulated end is to be used as spine. It is expossed to sourrounding with a temperature of 80°C and a heat transfer coefficient 55 W/m²°C.
A metallic rod (k = 32 W/m°C), 10 mm in diameter and 80 mm long, with an insulated end is …
fluids

heat and mass transfer

Mech_59 Asked on 29th September 2023 in Mechanical engineering.
- 428 views
- 1 answers
- 0 votes
What is the efficciency of a plate fin of length L = 1.5 cm and thickness 2 mm, (if k = 210 W/m-K, h = 285 W/m²k).
What is the efficciency of a plate fin of length L = 1.5 cm and thickness 2 mm, (if k …
fluids

heat and mass transfer

Mech_59 Asked on 28th September 2023 in Mechanical engineering.
- 1K views
- 1 answers
- 0 votes
It is required to heat oil to about 500°C for quenching purpose. A ladder is used in the furnace. The section of ladder is (10 x 20) mm². The sourroundings are at 27°C.
It is required to heat oil to about 500°C for quenching purpose. A ladder is used in the furnace. The …
fluids

heat and mass transfer

Mech_59 Asked on 28th September 2023 in Mechanical engineering.
- 2K views
- 1 answers
- 0 votes

Tags

LATEST QUESTIONS

Tags