Other engineering and technology Archives - Page 4 of 7

Question Cagtegory: Other engineering and technology

All Questions

Filter by

Questions Per Page:

In a manufecturing process, a transparent film is bonded to a substrate as shown in given figure. Assuming the following conditions T∞ = 20 °C, h = 50 W/(m2K) and T1 = 30 °C, calculate the heat flux q0 that is required to maintain the bonded surface at T0 = 60° C.
In a manufecturing process, a transparent film is bonded to a substrate as shown in given figure. To cure the …
fluids

heat and mass transfer

Mech_59 Asked on 25th July 2023 in Mechanical engineering.
- 661 views
- 1 answers
- 0 votes
A laboratory furnace wall is constructed of 0.2 m thick fire clay bricks (k = 1.0 W/m K). The maximum allowable heat transfer rate through the wall of the furnace is 900 W/m2, determine how thick must the insulating layer be?
A laboratory furnace wall is constructed of 0.2 m thick fire clay bricks (k = 1.0 W/m K). The wall …
fluids

heat and mass transfer

Mech_59 Asked on 17th July 2023 in Mechanical engineering.
- 467 views
- 1 answers
- 0 votes
A plane wall of a refrigerated van is made of 1.5mm steel sheet (k_s = 25W/(mK)) at the outer surface, 10 mm plywood (k_p = 0.05 W/(mK)) at the inner surface and 20 mm glass wool (k_G=0.01 W/(mK)) in between the outer and inner surfaces. Determine the individual components of the thermal resistance
A plane wall of a refrigerated van is made of 1.5mm steel sheet (k_s = 25W/(mK)) at the outer surface, …
fluids

heat and mass transfer

Mech_59 Asked on 17th July 2023 in Mechanical engineering.
- 505 views
- 1 answers
- 0 votes
A hot 16cm x 16cm x 16cm cubical iron block is cooled at an average rate of 80 W. What is the heat flux?
A hot 16cm x 16cm x 16cm cubical iron block is cooled at an average rate of 80 W. What …
fluids

heat and mass transfer

Mech_59 Asked on 17th July 2023 in Mechanical engineering.
- 542 views
- 1 answers
- 0 votes
A 1 kW electric resistance heater in a room is turned on and kept on for 50 minutes. What is the amount of energy transferred to the room by the heater?
A 1 kW electric resistance heater in a room is turned on and kept on for 50 minutes. What is …
fluids

heat and mass transfer

Mech_59 Asked on 17th July 2023 in Mechanical engineering.
- 487 views
- 1 answers
- 0 votes
A 2kW electric resistance heater submerged in 30 kg water is turned on and kept on for 10 min. What is the temperature rise of water.
A 2kW electric resistance heater submerged in 30 kg water is turned on and kept on for 10 min. During …
fluids

heat and mass transfer

Mech_59 Asked on 17th July 2023 in Mechanical engineering.
- 526 views
- 1 answers
- 0 votes
Eggs with a mass of 0.15 kg per egg and a specific heat of 3.32 kJ/kg.C are cooled from 32 degree Celsius to 10 degree Celsius at a rate of 300 eggs per minute. Compute the rate of heat removal from the eggs in kW.
Eggs with a mass of 0.15 kg per egg and a specific heat of 3.32 kJ/kg.C are cooled from 32 …
fluids

heat and mass transfer

Mech_59 Asked on 17th July 2023 in Mechanical engineering.
- 519 views
- 1 answers
- 0 votes
After sunset, radiant energy can be sensed by a person standing near a brick wall. What would be the radiant heat flux per square meter from a brick wall at this temperature?
After sunset, radiant energy can be sensed by a person standing near a brick wall. Such walls frequently have a …
fluids

heat and mass transfer

Mech_59 Asked on 12th July 2023 in Mechanical engineering.
- 569 views
- 1 answers
- 0 votes
The average forced convective heat transfer coefficcient for a hot fluid flowing over a cold surface is 200 W/(m^2C). Determine the heat transfer rate per unit surface area from the fliuid to the surface.
The average forced convective heat transfer coefficcient for a hot fluid flowing over a cold surface is 200 W/(m^2C). The …
fluids

heat and mass transfer

Mech_59 Asked on 10th July 2023 in Mechanical engineering.
- 520 views
- 1 answers
- 0 votes
A fluid flowing along a pipe line undergoes a throttling process from 10 bar to 1 bar is passing through a partially open valve. Before throttling, the specific volume of the fluid is 0.5 m^3/kg and after throttling is 2.0 m^3/kg. What is the change in specific internal energy during the throttling process?
A fluid flowing along a pipe line undergoes a throttling process from 10 bar to 1 bar is passing through …
Mech_59 Asked on 2nd December 2022 in Mechanical engineering.
- 541 views
- 1 answers
- 2 votes

Tags

LATEST QUESTIONS

Tags